HP DeskJet 3630 All-in-One Printer series
HP Deskjet 3630 has wireless capable mobile printing and easy to setup on ypou PCs and smart devices. It has all in one function to simplify tasks and user friendly display panel for controlling print scan and copy function. It is smart design to fit in your shelf and comes with fine printing quality.
How To Download and Install HP DeskJet 3630 All-in-One Printer series
- Open the HP printer software. For more information, see Open the HP printer software (Windows)
- Click Tools.
- Connect the printer flat end USB cable to the computer in the USB port
- Connect the rear end of the printer USB cable to the printer.
- The USB connection port is found near the power supply.
- The USB connection will be detected on the computer.
- You can find the connection status in the task bar for Windows.
- For mac you can find the connection status in system preferences.
1) Visit 123.hp.com and download the app using your internet browser.
2) Use Run prompt option or find the download file from the downloads and install the software.
3) Follow the instruction prompted on your screen.
4) The driver software will be installed and you can find it in the desktop.
2) Use Run prompt option or find the download file from the downloads and install the software.
3) Follow the instruction prompted on your screen.
4) The driver software will be installed and you can find it in the desktop.
How To Install INK HP DeskJet 3630 All-in-One Printer series
To replace the ink cartridges
1. Check that power is on.
2. Remove the ink cartridge.
a. Open the cartridge access door and wait for the print carriage to move to the center of the printer.
b. Press down to release the ink cartridge, and then remove it from the slot.
3. Insert a new ink cartridge.
a. Remove the ink cartridge from the packaging.
b. Remove the plastic tape using the pull tab.
NOTE: Do not touch the electrical contacts on the ink cartridge.
c. Slide the ink cartridge into the slot until it clicks into place.
d. Close the cartridge access door.
NOTE: The HP printer software prompts you to align the ink cartridges when you print a document after installing the new ink cartridge.
How To SETUP WIRLESS/WPS PIN/WIFI HP DeskJet 3630 All-in-One Printer series
Additional advanced settings are available from the printer's home page (embedded web server or EWS). For more information, see Embedded web server. This section contains the following topics:
● Set up the printer for wireless communication
● Change network settings
● Use Wi-Fi Direct Set up the printer for wireless communication
● Before you begin
● Set up the printer on your wireless network
● Change the connection type
● Test the wireless connection
● Turn on or off the wireless capability of the printer NOTE: If you encounter problems connecting the printer, see Network and connection issues. TIP: For more information about setting up and using the printer wirelessly, visit the HP Wireless Printing Center ( www.hp.com/go/wirelessprinting ). Before you begin
Ensure the following:
● The printer is not connected to the network using an Ethernet cable.
● The wireless network is set up and working properly.
● The printer and the computers that use the printer are on the same network (subnet). While connecting the printer, you might be prompted to enter the wireless network name (SSID) and a wireless password.
● The wireless network name is the name of your wireless network.
● The wireless password prevents other people from connecting to your wireless network without your permission. Depending on the level of security required, your wireless network might use either a WPA passphrase or WEP key. If you have not changed the network name or the security passkey since setting up your wireless network, you can sometimes find them on the back or side of the wireless router. If you cannot find the network name or the security password or cannot remember this information, see the documentation provided with your computer or with the wireless router. If you still cannot find this information, contact your network administrator or the person who set up the wireless network
Set up the printer on your wireless network Use the Wireless Setup Wizard from the printer control panel display to set up wireless communication.
NOTE: Before you proceed, go through the list at
Before you begin.
1. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, and then touch (Wireless).
2. Touch ( Settings ).
3. Touch Wireless Settings.
4. Touch Wireless Setup Wizard or Wi-Fi Protected Setup.
5. Follow the display instructions to complete the setup. If you are already using the printer with a different type of connection, such as a USB connection, follow the instructions in Change the connection type to set up the printer on your wireless network. Change the connection type After you have installed the HP printer software and connected the printer to your computer or to a network, you can use the software to change the connection type (for example, from a USB connection to a wireless connection). NOTE: Connecting an Ethernet cable turns off the wireless capability of the printer.
To change from an Ethernet connection to a wireless connection (Windows)
1. Remove the Ethernet cable from the printer.
2. Run the Wireless Setup Wizard to make the wireless connection. For more information, see Set up the printer on your wireless network.
To change from a USB connection to a wireless network (Windows)
Before you proceed, go through the list at Before you begin.
3. Click Device Setup & Software.
4. Select Convert a USB connected printer to wireless. Follow the onscreen instructions.
To change from a USB or Ethernet connection to a wireless connection (OS X)
1. Connect the printer to your wireless network.
2. Use 123.hp.com to change the software connection to wireless for this printer. Learn more about how to change from a USB to wireless connection.
Visit 123.hp.com/setup to go online for more information. At this time, this website might not be available in all languages.
To change from a wireless connection to a USB or Ethernet connection (Windows)
● Connect the USB or Ethernet cable to the printer.
To change from a wireless connection to a USB or Ethernet connection (OS X)
1. Open System Preferences .
2. Click Printers &Scanners .
3. Select your printer in the left pane and click - at the bottom of the list. Do the same for the fax entry, if there is one for the current connection.
4. Connect the printer to your computer or network using either a USB or Ethernet cable.
5. Click + below the list of printers at the left.
6. Select the new printer from the list.
7. Choose your printer model name from the Use pop-up menu.
8. Click Add. Test the wireless connection Print the wireless test report for information about the printer wireless connection. The wireless test report provides information about the printer status, hardware (MAC) address, and IP address. If there is a problem with the wireless connection or if a wireless connection attempt failed, the wireless test report also provides diagnostic information. If the printer is connected to a network, the test report displays details about the network settings.
To print the wireless test report
1. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, touch (the Wireless button), and then touch ( Settings ).
2. Touch Print Reports.
3. Touch Wireless Test Report. Turn on or off the wireless capability of the printer The blue Wireless light on the printer control panel is lit when the wireless capability of the printer is on.
NOTE: Connecting an Ethernet cable to the printer automatically turns off the wireless capability and the Wireless light.
1. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, touch (the Wireless button), and then touch ( Settings ).
2. Touch Wireless Settings.
3. Touch Wireless to switch it on or off. Change network settings From the printer control panel, you can set up and manage your printer's wireless connection and perform a variety of network management tasks. This includes viewing and changing network settings, restoring network defaults, and turning the wireless function on or off.
CAUTION: Network settings are provided for your convenience. However, unless you are an advanced user, you should not change some of these settings (such as the link speed, IP settings, default gateway, and firewall settings
To print network settings
Do one of the following:
● From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard. Touch (Wireless) or (Ethernet) to display the network status screen. Touch Print Details to print the network configuration page.
● From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, touch ( Setup ), touch Reports , and then touch Network &onfiJurDtLon Report. To set the link speed You can change the speed at which data is transmitted over the network. The default is Automatic.
1. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, touch ( Setup ), and then touch Network Setup.
2. Touch Ethernet Settings.
3. Select Advanced Settings.
4. Touch Link Speed.
5. Touch the appropriate option that matches your network hardware. To change IP settings The default IP setting for the IP settings is Automatic, which sets the IP settings automatically. If you are an advanced user and want to use different settings (such as the IP address, subnet mask, or the default gateway), you can change them manually.
TIP: Before setting a manual IP address, it is recommended to first connect the printer to the network using Automatic mode. This allows the router to configure the printer with other needed settings like subnet mask, default gateway and DNS address.
CAUTION: Be careful when manually assigning an IP address. If you enter an invalid IP address during the installation, your network components cannot connect with the printer.
1. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, touch ( Setup ), and then touch Network Setup.
2. Touch Ethernet Settings or Wireless Settings.
3. Touch Advanced Settings.
4. Touch IP Settings. A message appears warning that changing the IP address removes the printer from the network. Touch OK to continue.
5. To change the settings manually, touch Manual (Static), and then enter the appropriate information for the following settings:
● IP Address
● Subnet Mask
● Default Gateway
● DNS Address
6. Enter your changes, and then touch Done .
7. Touch OK . Use Wi-Fi Direct With Wi-Fi Direct, you can print wirelessly from a computer, smart phone, tablet, or other wireless-capable device—without connecting to an existing wireless network. Guidelines for using Wi-Fi Direct
● Make sure your computer or mobile device has the necessary software. – If you are using a computer, make sure you have installed the HP printer software. If you have not installed the HP printer software on the computer, connect to Wi-Fi Direct first and then install the printer software. Select Wireless when prompted by the printer software for a connection type. – If you are using a mobile device, make sure you have installed a compatible printing app. For more information about mobile printing, visit www.hp.com/global/us/en/eprint/ mobile_printing_apps.html. 123.hp.com/setup officejet pro
● Make sure Wi-Fi Direct for your printer is turned on.
● Up to five computers and mobile devices can use the same Wi-Fi Direct connection.
● Wi-Fi Direct can be used while the printer is also connected either to a computer using a USB cable or to a network using a wireless connection.
● Wi-Fi Direct cannot be used to connect a computer, mobile device, or printer to the Internet.
To turn on Wi-Fi Direct
1. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, and then touch (Wi-Fi Direct).
2. Touch ( Settings ).
3. If the display shows that Wi-Fi Direct is 2ff , touch Wi-Fi Direct and then switch it on.
TIP: You can also turn on Wi-Fi Direct from the EWS.
For more information about using the EWS, see Embedded web server.
To change connection method
1. From the printer control panel, touch or swipe down the tab at the top of the screen to open the Dashboard, and then touch (Wi-Fi Direct).
2. Touch ( Settings ).
3. Touch Connection Method and then select Automatic or Manual .
To print from a wireless-capable mobile device that supports Wi-Fi Direct Make sure you have installed the latest version of HP Print Service Plugin on your mobile device. You can download this plugin from the Google Play application store.
1. Make sure you have turned on Wi-Fi Direct on the printer.
2. Turn on Wi-Fi Direct on your mobile device. For more information, see the documentation provided with the mobile device.
3. From your mobile device, select a document from a print enabled application, and then select the option to print the document. The list of available printers appears.
4. From the list of available printers, choose the Wi-Fi Direct name shown such as DIRECT-**-HP 2ffLce-et Pro 6960 (where ** are the unique characters to identify your printer and XXXX is the printer model located on the printer) to connect your mobile device. If the mobile device is not automatically connected to the printer, follow the instructions on the printer control panel to connect to the printer. If a PIN code is displayed on the printer control panel, enter the PIN code on your mobile device. When the mobile device is successfully connected to the printer, the printer starts printing.
To print from a wireless-capable mobile device that does not support Wi-Fi Direct
Make sure you have installed a compatible printing app on your mobile device. For more information, visit www.hp.com/global/us/en/eprint/mobile_printing_apps.html. 123.hp.com/setup oj6968 network
1. Make sure you have turned on Wi-Fi Direct on the printer.
2. Turn on the Wi-Fi connection on your mobile device. For more information, see the documentation provided with the mobile device.
NOTE: If your mobile device does not support Wi-Fi, you are not able to use Wi-Fi Direct.
3. From the mobile device, connect to a new network. Use the process you normally use to connect to a new wireless network or hotspot. Choose the Wi-Fi Direct name from the list of wireless networks shown such as DIRECT-**-HP 2ffLce-et Pro 6960 (where ** are the unique characters to identify your printer). Enter the Wi-Fi Direct password when prompted.
4. Print your document.
To print from a wireless-capable computer (Windows)
1. Make sure you have turned on Wi-Fi Direct on the printer.
2. Turn on the computer's Wi-Fi connection. For more information, see the documentation provided with the computer. NOTE: If your computer does not support Wi-Fi, you are not able to use Wi-Fi Direct.
3. From the computer, connect to a new network. Use the process you normally use to connect to a new wireless network or hotspot. Choose the Wi-Fi Direct name from the list of wireless networks shown such as DIRECT-**-HP 2ffLce-et Pro 6960 (where ** are the unique characters to identify your printer). Enter the Wi-Fi Direct password when prompted.
4. Proceed to step 5 if the printer has been installed and connected to the computer over a wireless network. If the printer has been installed and connected to your computer with a USB cable, follow the steps below to install the printer software using the Wi-Fi Direct connection.
a. Open the HP printer software. For more information, see Open the HP printer software (Windows). b. Click Tools.
c. Click Device Setup & Software, and then select Connect a new device.
NOTE: If you have previously installed the printer over USB and want to convert to Wi-Fi Direct, do not select the Convert a USB connected printer to wireless option.
d. When the Connection Options software screen appears, select Wireless.
e. Select your HP printer from the detected printer list.
f. Follow the onscreen instructions.
5. Print your document.
To print from a wireless-capable computer (OS X)
1. Make sure you have turned on Wi-Fi Direct on the printer.
2. Turn on Wi-Fi on the computer.
For more information, see the documentation provided by Apple.
3. Click the Wi-Fi icon and choose the Wi-Fi Direct name, such as DIRECT-**-HP 2ffLce-et Pro 6960 (where ** are the unique characters to identify your printer). If Wi-Fi Direct is turned on with security, enter the password when prompted.
4. Add the printer.
a. Open System Preferences .
b. Depending on your operating system, click Printers &Scanners .
c. Click + below the list of printers at the left.
d. Select the printer from the list of detected printers (the word “Bonjour” is listed the right column beside the printer name), and click Add. Click here for online troubleshooting for Wi-Fi Direct, or for more help with setting up Wi-Fi Direct.
At this time, this website might not be available in all languages.
No comments:
Post a Comment
Note: Only a member of this blog may post a comment.